Post by moncler1 on Jan 3, 2012 4:41:35 GMT -5
When my neighbor first decided to install a paver-block patio, he chose paver stones for several reasons. He thought they would last longer than other materials like wood, or poured concrete, and that they would be maintenance free. While they do look great and they're incredibly durable, it wasn't long before he learned that they aren't completely maintenance free.
After several seasons of rain, snow and sun, the patio didn't look as good as when he had it installed. The sun was beginning to fade the color in some areas, the sand between the stones had been washed away, and weeds had started growing in the gaps between the pavers. He even began to see ant colonies forming using his precious paver sand as their new home.
The solution to his problem was fairly simple. It was time to clean the patio up and seal it for protection. "Just observe these simple 11 keys", I told him, "and when you're done your patio will look like it was done by the Pros!"
1. Take your time. With every project that I undertake, I can't stress this point enough. When you rush a project through you make mistakes, and mistakes are what the pros are able to avoid. Sometimes it's just a matter of cleaning the surface a little better, or rinsing things off a little more. Maybe it's allowing a little more time between coats for your sealer to dry or waiting a few more hours before re-installing your patio furniture. The chances are much better that when the work is all done, you'll look at the finished result and be satisfied that it turned out just as you had hoped it moncler uk coats would.
2. Often times when you inspect the patio, prior to washing you'll notice stains. Leaves that have remained on the patio can leave tannin stains. Iron furniture that sits on the patio can leave rust stains. Whatever stains you find need to be removed prior to sealing or they will become permanent, so now is the time to work on them. The simplest way to get the stains out is by using an acid cleaner. Conventional muriatic acid works well and it's cheap, but I hate it. If you get it on your skin it burns and the vapors from it are just terrible. Instead, I use a "safer" cleaner, such as Defy Safer Masonry Cleaner. For severe stains, I simply pour a little cleaner at full strength on the stain and give it a few minutes to work before rinsing. If the whole patio is fairly dirty, dilute the cleaner 4:1 (four parts water to one part cleaner) and using a garden-type pump up sprayer, spray the entire surface with cleaner. Allow the cleaner to remain wet on the surface for 5 minutes or so, and then rinse using a power washer.
3. In regard to the prep work, sealing you patio isn't much different than staining your deck or painting your house. Much of the quality of the job comes down to how well you prepare the surface.
Patios that have weathered will often times have mildew, moss and algae growing on the stones and in the sand between the joints. Weeds that have begun to grow as well as any other foreign debris need to be removed, and for a patio that means a good cleaning. The easiest way to clean things off is with a power washer.
Make certain that you select a washer with enough power to do the job. I try to never use anything rated less than 2400 p.s.i. Select a tip that will fan the water out slightly, 15?or so. Also, always work in sections.
Patios should be constructed so that water runs away from the home. So begin working near the house or the high side of the slope of the patio. Rinse debris down the patio's natural flow, away from the house. You'll loose some of the sand between the joints during the cleaning process and that's ok. We'll replace the sand once the patio is cleaned up. Just be careful not to blow out more sand than is necessary while doing your cleaning.
4. With the patio now cleaned, look around and inspect the condition of the pavers. Over time, paver stones can settle or shift, making them unlevel. If you have some bricks that are out of place, using a screwdriver and a stiff putty knife, pry the uneven stones out. Once removed, you can add a little sand, smooth it Moncler Jackets out with the blade of your putty knife, and re-install the bricks.
5. The last remaining step in getting the patio ready to seal is to re-grout the joints between the stones with fresh sand. This step isn't hard, but it does take a little time so be patient. To do this, I use a fine grade of play box sand. Pour a small amount on the patio and begin sweeping it into the joints using a push-broom. Sweep in both directions; back-to-front and left-to-right to insure the joints get completely filled. As the sand gets used up by filling the joints pour a little more onto the patio and keep sweeping.
6. This is the part you're going to love. Go take a break! Remember when we started I said to take your time? After all of the cleaning that we did, moncler coats in canada the ground under those pavers is soaking wet and needs to dry out. Give the patio a couple of good, hot sunny days to dry out before applying any sealer. If you don't, you could end up trapping moisture under the sealer and the whole project will turn a milky white color...yuck!
7. It's time to pick out your sealer now and the choices are solvent-based products or water-based products. I hate solvents! "Why?" you ask. Here's why:
1. They're bad for our environment.
2. They kill grass and flowers.
3. They smell terrible.
4. Everything has to be cleaned up with messy solvents.
Water-base sealers are a much better choice. Besides being both easy to use and easy on the environment, they offer another amazing advantage. They "stabilize" the sand. When cured, water-based sealers such as DEFY Paver Sealer will harden the joint sand and lock it into place. This prevents it from washing out during future rains.
8. Every manufacturer's product can be a little different so always read the directions. It only takes a few minutes but it will ensure that you have all the right information before you get started. Pay attention to details such as how many coats of sealer to apply, how long to wait between coats, how to properly apply the product and how to clean it up. There are any number of variations to these questions and more. Read the label first and you'll be likely to get it right the first time.
9. Now the fun begins...applying the sealer. To do this, I love to use a garden-type pump up sprayer but I'll warn you in advance, don't buy a cheap one! The better sprayers (they usually cost over $50) have a metal fan-style spray tip and do a much better job than the inexpensive weed sprayers. When you're looking for a sprayer, the key here is to look for a "fan-style tip".
The patio edges can be cut-in using a 4" nylon brush and then you're ready to start spraying. Water-based sealers normally require two coats to be applied. Once you've cut-in the edges, spray the entire patio with the first coat. Then wait for the sealer to dry enough that it can walked on, and do the same thing all over again. If you get it too heavy and the sealer starts to puddle, use the brush to get rid of the puddling by brushing it out.
10. Ok, if a little is good then a lot must be better, right? No! Remember, we're sealing concrete paver stones and these stones are sitting on a bed of sand. When the sand gets wet and then the sun comes out, these pavers need to breathe, meaning they need to let any water vapors pass through them. When too much sealer is applied, the water vapor can no longer pass through, which results in a white "blushing" effect or Moncler Coats Sale even potentially peeling. Limit your application to two coats and you won't have a problem.
After several seasons of rain, snow and sun, the patio didn't look as good as when he had it installed. The sun was beginning to fade the color in some areas, the sand between the stones had been washed away, and weeds had started growing in the gaps between the pavers. He even began to see ant colonies forming using his precious paver sand as their new home.
The solution to his problem was fairly simple. It was time to clean the patio up and seal it for protection. "Just observe these simple 11 keys", I told him, "and when you're done your patio will look like it was done by the Pros!"
1. Take your time. With every project that I undertake, I can't stress this point enough. When you rush a project through you make mistakes, and mistakes are what the pros are able to avoid. Sometimes it's just a matter of cleaning the surface a little better, or rinsing things off a little more. Maybe it's allowing a little more time between coats for your sealer to dry or waiting a few more hours before re-installing your patio furniture. The chances are much better that when the work is all done, you'll look at the finished result and be satisfied that it turned out just as you had hoped it moncler uk coats would.
2. Often times when you inspect the patio, prior to washing you'll notice stains. Leaves that have remained on the patio can leave tannin stains. Iron furniture that sits on the patio can leave rust stains. Whatever stains you find need to be removed prior to sealing or they will become permanent, so now is the time to work on them. The simplest way to get the stains out is by using an acid cleaner. Conventional muriatic acid works well and it's cheap, but I hate it. If you get it on your skin it burns and the vapors from it are just terrible. Instead, I use a "safer" cleaner, such as Defy Safer Masonry Cleaner. For severe stains, I simply pour a little cleaner at full strength on the stain and give it a few minutes to work before rinsing. If the whole patio is fairly dirty, dilute the cleaner 4:1 (four parts water to one part cleaner) and using a garden-type pump up sprayer, spray the entire surface with cleaner. Allow the cleaner to remain wet on the surface for 5 minutes or so, and then rinse using a power washer.
3. In regard to the prep work, sealing you patio isn't much different than staining your deck or painting your house. Much of the quality of the job comes down to how well you prepare the surface.
Patios that have weathered will often times have mildew, moss and algae growing on the stones and in the sand between the joints. Weeds that have begun to grow as well as any other foreign debris need to be removed, and for a patio that means a good cleaning. The easiest way to clean things off is with a power washer.
Make certain that you select a washer with enough power to do the job. I try to never use anything rated less than 2400 p.s.i. Select a tip that will fan the water out slightly, 15?or so. Also, always work in sections.
Patios should be constructed so that water runs away from the home. So begin working near the house or the high side of the slope of the patio. Rinse debris down the patio's natural flow, away from the house. You'll loose some of the sand between the joints during the cleaning process and that's ok. We'll replace the sand once the patio is cleaned up. Just be careful not to blow out more sand than is necessary while doing your cleaning.
4. With the patio now cleaned, look around and inspect the condition of the pavers. Over time, paver stones can settle or shift, making them unlevel. If you have some bricks that are out of place, using a screwdriver and a stiff putty knife, pry the uneven stones out. Once removed, you can add a little sand, smooth it Moncler Jackets out with the blade of your putty knife, and re-install the bricks.
5. The last remaining step in getting the patio ready to seal is to re-grout the joints between the stones with fresh sand. This step isn't hard, but it does take a little time so be patient. To do this, I use a fine grade of play box sand. Pour a small amount on the patio and begin sweeping it into the joints using a push-broom. Sweep in both directions; back-to-front and left-to-right to insure the joints get completely filled. As the sand gets used up by filling the joints pour a little more onto the patio and keep sweeping.
6. This is the part you're going to love. Go take a break! Remember when we started I said to take your time? After all of the cleaning that we did, moncler coats in canada the ground under those pavers is soaking wet and needs to dry out. Give the patio a couple of good, hot sunny days to dry out before applying any sealer. If you don't, you could end up trapping moisture under the sealer and the whole project will turn a milky white color...yuck!
7. It's time to pick out your sealer now and the choices are solvent-based products or water-based products. I hate solvents! "Why?" you ask. Here's why:
1. They're bad for our environment.
2. They kill grass and flowers.
3. They smell terrible.
4. Everything has to be cleaned up with messy solvents.
Water-base sealers are a much better choice. Besides being both easy to use and easy on the environment, they offer another amazing advantage. They "stabilize" the sand. When cured, water-based sealers such as DEFY Paver Sealer will harden the joint sand and lock it into place. This prevents it from washing out during future rains.
8. Every manufacturer's product can be a little different so always read the directions. It only takes a few minutes but it will ensure that you have all the right information before you get started. Pay attention to details such as how many coats of sealer to apply, how long to wait between coats, how to properly apply the product and how to clean it up. There are any number of variations to these questions and more. Read the label first and you'll be likely to get it right the first time.
9. Now the fun begins...applying the sealer. To do this, I love to use a garden-type pump up sprayer but I'll warn you in advance, don't buy a cheap one! The better sprayers (they usually cost over $50) have a metal fan-style spray tip and do a much better job than the inexpensive weed sprayers. When you're looking for a sprayer, the key here is to look for a "fan-style tip".
The patio edges can be cut-in using a 4" nylon brush and then you're ready to start spraying. Water-based sealers normally require two coats to be applied. Once you've cut-in the edges, spray the entire patio with the first coat. Then wait for the sealer to dry enough that it can walked on, and do the same thing all over again. If you get it too heavy and the sealer starts to puddle, use the brush to get rid of the puddling by brushing it out.
10. Ok, if a little is good then a lot must be better, right? No! Remember, we're sealing concrete paver stones and these stones are sitting on a bed of sand. When the sand gets wet and then the sun comes out, these pavers need to breathe, meaning they need to let any water vapors pass through them. When too much sealer is applied, the water vapor can no longer pass through, which results in a white "blushing" effect or Moncler Coats Sale even potentially peeling. Limit your application to two coats and you won't have a problem.